Quick Answer: How is torque calculated in an induction motor?

Torque of a three phase induction motor is proportional to flux per stator pole, rotor current and the power factor of the rotor. T ∝ ɸ I2 cosɸ2 OR T = k ɸ I2 cosɸ2 .

How do you calculate motor torque?

To calculate load torque, multiply the force (F) by the distance away from the rotational axis, which is the radius of the pulley (r). If the mass of the load (blue box) is 20 Newtons, and the radius of the pulley is 5 cm away, then the required torque for the application is 20 N x 0.05 m = 1 Nm.

How do you calculate maximum torque of an induction motor?

So, when slip s = R2 / X2, the torque will be maximum and this slip is called maximum slip Sm and it is defined as the ratio of rotor resistance to that of rotor reactance. NOTE: At starting S = 1, so the maximum starting torque occur when rotor resistance is equal to rotor reactance.

How is torque calculated?

The magnitude of a torque about a fixed axis is calculated by finding the lever arm to the point where the force is applied and using the relation |→τ|=r⊥F | τ → | = r ⊥ F , where r⊥ is the perpendicular distance from the axis to the line upon which the force vector lies.

IMPORTANT:  At what percentage of CCA should a car battery be replaced?

What is the torque of a motor?

Torque: The torque output of a motor is the amount of rotational force that the motor develops. The torque of a small electric motor is commonly measured in either inch pounds (in-lbs), Newton meters (N-m) or other directly converted units of measure.

How do you calculate maximum torque of a motor?

Calculate torque (T) using the formula T = 5,252 x horsepower/rpm. The results are measured in pound-feet. For example, if you have a 40-horsepower motor designed to operate at a peak of 1,200 rpm, the formula would be T = (5,252 x 40)/1200 = 175.07 lb. -feet.

When torque in an induction motor is maximum?

Hence, the developed torque is maximum when the rotor resistance per phase is equal to the rotor reactance per phase under running conditions. By putting the value of sX20 = R2 in equation (1) we get the equation for maximum torque.

What is load torque in induction motor?

The Full-load Torque is the torque required to produce the rated power of an electrical motor at full-load speed. In imperial units the Full-load Torque can be expressed as. T = 5252 Php / nr (1)

How do you calculate maximum torque?

Torque on the loop can be found using τ=NIABsinθ τ = N I A B sin ⁡ . Maximum torque occurs when θ = 90º and sin θ = 1.

How do you calculate rpm torque?

When you choose torque, this calculator will measure the approximate torque of an engine based on the horsepower, multiplied by 5,252 (conversion between foot-pounds and horsepower), divided by the RPM of the engine. For example, if your engine has 350 horsepower then the torque would be 367 foot-pounds, at 5,000 RPM.

IMPORTANT:  Frequent question: Can a mechanic keep your car Florida?

How do you calculate torque output?

Divide the diameter of the output gear by the diameter of the input gear. Multiply the torque of the motor by the gear ratio to get the output torque. For example, a motor that puts out 10 lb. -feet of torque used with a gear reducer with a 10:1 gear ratio will give you 100 lb.

How does torque work in a motor?

That torque is created by the pistons within an engine as they reciprocate up and down on the engine’s crankshaft, causing it to rotate (or twist), continuously. This torque is then transferred to the vehicle’s wheels through the transmission and drivetrain.

What is the relation between torque and speed in induction motor?

Torque is inversely proportional to speed. Thus, when speed increases, torque will decrease.