You asked: Will a v6 Transmission fit a v8 Chevy?

Is a v6 transmission the same as a v8?

Most of the internals are the same, but the case is different between the v6 and v8. You wouldn’t be able to just take it out and put it in the other truck.

Will a v6 4L60E fit in a v8?

Registered. The 4L60E in the NNBS is identical except the harness in 2009-2013. 2007.5-2008 are the exact same regardless if is v6 or v8. The converter or flexplate may be different tho.

Will a v8 bolt up to a v6 transmission?

v8 swap is very easy, the stock v6 tranny will work but it won’t hold up as well as the v8 tranny, and get the v8 computer and wire in the extra 2 injectors into the wiring harness and your set.

Can I swap a v6 for a v8?

There are at least a dozen different companies that make V6-to-V8 conversion kits that include motor mounts, exhaust headers and sometimes a transmission mount. These kits give you the parts you’ll need to physically fit the engine into the truck, but you’re going to have to supply everything else.

IMPORTANT:  Question: How do I get my windshield wipers back to work?

Is the V6 and V8 700R4 the same?

V6 with 700R4 has same trans as V8 with 700R4. They do have different torque convertors.

What is the difference 700R4 4L60?

You can’t tell the difference between a 700R4 and a 4L60E by the oil pan as they are nearly the same. If the transmission has a large 18-pin electronic connector above the passenger side pan rail, it’s a 4L60E, as seen here. If it has a cable connection near the cooler lines on the passenger’s side, that’s a 700R4.

What’s the difference between 4L60 and 4L60E?

The rear output housing is configured with a six-bolt pattern in late model 4L60E transmissions. The 4L60 transmission is configured with a four-bolt pattern. The bolt pattern is not a guaranteed distinction, however, as early 4L60E transmissions, manufactured from 1992 through 1997, also have a four-bolt pattern.

What years will a 4L60E transmission fit?

700R4/4L60E/4L65E Year Ranges

Year Ranges Transmission Pan/Filter
1994-1996 4L60E Shallow
1997 4L60E Shallow – Early Deep – Late
1998-2000 4L60E Deep
2001-2003 4L60E/4L65E Deep

What motor does a 4L60E fit?

The front face 4L60-E is natively compatible with either the Chevrolet 90 degree “Small Block” & “Big Block” patterned engines (image, left), including the V6, V8 & I6.

What vehicles have the 42RE transmission?

How Do I Order?

  • 1989-2003 Dodge Dakota.
  • 1998-2000 Dodge Durango.
  • 1989-2001 Dodge Ram pickup 150 / 1500.
  • 1989-2003 Dodge Ram Van B150 / B250.
  • 1993-2004 Jeep Grand Cherokee.
  • 1996-1998 Jeep Grand Cherokee 5.2 V8.

How do I identify my Dodge transmission?

Open the hood of the truck and locate the transmission fluid container. The vehicle’s transmission information will be located on a plate adjacent to the container. Read the vehicle owner manual and you will be able to identify the vehicle’s transmission information.

IMPORTANT:  What states have cars without rust?

What transmission does my Dodge Dakota have?

The Dodge Dakota was equipped with the 42RE (A500), 46RE or the 545RFE transmission. Late model 2011+ Dakota’s are called the Ram Dakota and had the 42RLE transmission.

How much would it cost to convert a V6 to V8?

New engines start at around $4,000 for a 4-cylinder, around $5,500 for a V6 and $7,000 for a V8.

How much does it cost to do a V8 swap?

We’ll get into the specifics of price in a bit, but at a minimum, you should expect to pay at least $3,000 dollars for an engine swap if you’re paying a mechanic to get it done.

How much does an engine swap cost?

As a result, expect to spend between $500 and $1,500 in labor costs, in addition to anywhere from $500 for a short block engine to $9,000 for a complete, high-performance engine. Remember that depending on the type of engine chosen, you’ll need to pay for additional parts to complete the block as well.